Choose Country of Delivery
Please select the country of delivery to show the prices with the correct VAT rate:Ford Ranger PX - PX III (2018 - 2022)
| Show 1 to 20 (of in total 20 products) |
Front Axle
Axle:
Front Axle
Kit includes Boot and Cir Clips for one Control Arm repair kit for SuperPro Roll Controll arms only
Quantity required for one car:
2
Fitting Difficulty:
Fitting Time (min):
30
Axle:
Front Axle
Left and Right Arms for Lifted Vehicles with Caster and Camber Correction
Arms fitted with Uprated Ball joints and SuperPro Bushes to reduce Arm movement +/- 2 Degrees of Camber Adjustment and 0 to +4 Degrees of Caster Adjustment. Supplied with Camber & Caster Adjustable Ball Joints. Fitted with SuperPro Bushings
Quantity required for one car:
1
Fitting Difficulty:
Fitting Time (hours): 2
Axle:
Front Axle
Getting the correct alignment on your lifted Ranger / BT-50 is no longer a problem.
The SuperPro Fixed Offset Upper Control Arm is an all-in-one solution for any vehicle that has been lifted between 40mm and 65mm (2.5”). Providing an increase between 2.5 and 3.5 degrees of caster and up to 1.5 degrees of negative camber increase (figures quoted are based off a 50mm L ...
Quantity required for one car:
1
Fitting Time (hours): 2
Axle:
Front Axle
Suits Lifted vehicles. It is supplied complete with all required spacers, bolts, washers and nuts. When lifting the Ford Ranger PX 4WD, the Constant Velocity (CV) joints are put on an increased angle, helping to accelerate the wear on the joint and putting additional stress on the CV boots that will lead to splitting and premature failure of the CV. The SuperPro bolt on kit corre ...
Quantity required for one car:
1
Fitting Time (hours): 3
Axle:
Front Axle
12mm Ball Joint Adjustable Link Vehicle Application Information: Minimum Length 320 mm - Maximum Length 365 mm 12mm Ball Joint Adjustable Link, Minimum Length 320 mm - Maximum Length 365 mm
Quantity required for one car:
1
Fitting Difficulty:
Fitting Time (min): 60
Axle:
Front Axle
Quantity required for one car:
1
Fitting Difficulty:
Fitting Time (hours): 3
Axle:
Front Axle
Alignment Correction
Camber Adjustment +/- 1 Degree Camber Adjustment available
Quantity required for one car:
1
Fitting Difficulty:
Fitting Time (hours): 3
Axle:
Front Axle
Standard Replacement
Quantity required for one car:
1
Fitting Difficulty:
Fitting Time (hours): 3
Rear Axle
Axle:
Rear Axle
Contains Greasable Shackles and Fixed Pins with all SuperPro Bushings
Quantity required for one car:
1
Fitting Difficulty:
Fitting Time (min): 60
Axle:
Rear Axle
To be used with aftermarket Greaseable Fixed Pins Side impact protection for the fuel tank when greaseable pins a fitted from the outside on the LHS of the vehicle
Quantity required for one car:
1
Fitting Difficulty:
Axle:
Rear Axle
Quantity required for one car:
1
Axle:
Rear Axle
Quantity required for one car:
1
Fitting Difficulty:
Fitting Time (hours): 3
Axle:
Rear Axle
Quantity required for one car:
1
Fitting Difficulty:
Fitting Time (hours): 1.5
Axle:
Rear Axle
Quantity required for one car:
1
Fitting Difficulty:
Fitting Time (hours): 1.5
Axle:
Rear Axle
For vehicles without AdBlue tank
Quantity required for one car:
1
Fitting Difficulty:
Fitting Time (hours): 4
Axle:
Rear Axle
Fits vehicles with AdBlue tank
Quantity required for one car:
1
Fitting Difficulty:
Fitting Time (hours): 4
Axle:
Rear Axle
Fits vehicles without AdBlue tank
Quantity required for one car:
1
Fitting Difficulty:
Fitting Time (hours): 4
| Show 1 to 20 (of in total 20 products) |
